How To Make An Orgonite Chembuster That Will Help Heal The Planet

What you’ll need:

Materials:

CRYSTALS
COPPER PIPES
PIPE COUPLERS
METAL SHAVINGS
PLYWOOD PIECES (3 total)
RESIN
2 GALLON BUCKET

Tools:

DRILL
FLAT 1 1/4 INCH AUGER BIT
fLAT 1 1/8 INCH BIT
MASKING TAPE
HEAVY DUTY GLUE
MIXING DOWEL
YOUR HANDS

Here’s a more detailed list:

CRYSTALS: 6 Quartz and 6 Citrine crystals. 2″ in length, less than an inch in width. The most convenient way is to order online, try http://bit.ly/quartzCrystals.

COPPER PIPES:

1 standard Type M, 6 foot long, one-inch diameter copper pipe. Cut into six 12″ pieces.

3 standard type M, 10 foot long, one-inch diameter copper pipes. Cut each pipe in half to get six 5″ pipes.

PIPE COUPLERS: 6 Couplers that allow pipes to enter from both sides to meet in the middle.

METAL SHAVINGS: Metal shavings from machine shops are perfect. Get as much as you can. Fill a one-gallon bucket with metal shavings, that should be enough. And if different metals are available, even better.

PLYWOOD: 3 pieces of 3/4” exterior plywood. They should be cut to fit snugly within the 2-gallon bucket. Here are the templates you’ll need:

TEMPLATE 1: 3/4 inch plywood is used for the circular base of the 6 copper pipes with endcaps. The pipes are placed in a smaller circle that has a 2 1/2 inch diameter–so that the pipes’ centers are 2 1/2 inches apart. Use the 1 1/4″ drill bit to make the holes.

TEMPLATE 2: This wooden piece will go inside the rim, but you’ll only use it to get the pipes parallel to each other, then you’ll remove it. So it’s important to cut away some of the wood so you can fit your hand underneath it to pull it out. Use the 1 1/8″ drill bit to make the six holes.

TEMPLATE 3: This piece goes near the open ends of the copper pipes. It’s purpose is to align the pipes and maintain them parallel. The circular piece has a 4″ radius, and 1 1/8″ holes drilled on a circle with a 2 1/2″ radius.

RESIN: You have several options here. Polyester resin works well. Epoxy also works, as does Envirotech resin from www.eti-usa.com (this sets quickly, so you’ll need to be experienced with it). But if you’re planning on making a lot of these units, it’s much less expensive to order resin in 5-gallon buckets online. Try a surfboard or boat manufacturing supply company. Home Depot resin prices aren’t cheap–$24 per gallon.

BUCKET: 9″ in diameter, 9″ deep. 2 gallon plastic buckets from the Home Depot paint department are great for this but any other heavy duty 2 gallon bucket will do.

MASKING TAPE: You will use it to tape the open ends of the 12″ copper pipes to keep metal shavings from falling in while you’re adding resin and mixing in the metal shavings.

HEAVY DUTY GLUE: Try Goop glue.

__________________________________________________________________

How To Make An Orgonite Chembuster

The Brief:

Essentially, you’ll be inserting crystals inside cut pieces of rubber hose, which will then go into the 12″ copper pipe segments. You’ll seal one end of the pipes with the endcaps and tape the open ends closed, so that no metal shavings accidentally fall inside it while you’re pouring resin and mixing in metal shavings.

The 12″ pipes will then go inside the bucket in a circular formation. Use the wooden templates to hold the geometry together and keep the pipes parallel.

In goes the catalyzed resin mixed with metal shavings. Do this in three parts, waiting for each to harden before continuing to fill. When the whole bucket of resin has hardened, attach the 5 foot copper pipes using the couplers, and you’re done.

Put it to work in a safe and secret, but most of all, strategic location. Pull off the 5 foot lengths of copper pipe for increased portability.

How To Make An Orgonite Chembuster

The Details:

Start by sending a strong positive intention to each crystal, or all of them together at once. Positive intention is a clear thought that you hold for a time in the center of your mind, then send out to the crystals.

If you want to increase the power of this intention, meditate first. Once you have cleared your mind of all daily clutter and stopped any internal dialogue, form and sustain the following intention very clearly in your mind:

This thought should be that your crystals work together to attract and transmute negative orgone energy into positive orgone enery for the benefit of our planet and all of the living beings on it.

Insert each crystal into a cut piece of rubber hose, so that the fit is as tight as possible. This will provide the pressure needed to induce the piezoelectric effect of the crystals.

Place at least 2 crystals–keep in mind that you can place up to seven–in each 12″ copper pipe. Glue the hose pieces and crystals to the inside of copper pipe. Seal it with the endcap. Tape the open ends of the pipes to prevent metal particles from falling inside them while you add resin + metal shavings.

Pour about an inch of catalyzed resin into bucket. Stir in metal shavings until you have a flat surface; use 1 part metal shavings to one part resin. Note that resin is flammable. Hint: Do this in a warm, well-ventilated area.

Remove the tape over the open ends of the pipes. Place wooden TEMPLATE 1 onto resin before it hardens; do not force the wooden piece to the bottom of bucket, just place it onto the resin surface.

Get the six pipes in place; they should fit tightly within the six 1 1/4″ holes in TEMPLATE 1. The 12″ pipes should be in a circle, already capped with at least one quartz and one citrine crystal inside.

Now add a half gallon of catalyzed resin while mixing in handfuls of metal shavings with a dowel. Use the same ratio: one-part resin for one-part metal shavings.

After you’ve added the second layer of resin + metal shavings, remove the tape from the open ends of the copper pipes. Move the wooden TEMPLATE 2 downward carefully on the copper pipes until it fits within the bucket rim. Push it down so it is a snug fit. Add the COUPLERS and 5 foot pipes onto the 12″ base pipes.

Bring TEMPLATE 3 onto the copper pipes; it should remain near the top of the pipes. Turn it as needed so that the pipes are parallel to each other.

Wait for resin + metal shavings to harden, then remove TEMPLATE 2–you’ll have to remove TEMPLATE 3 first to get TEMPLATE 2 out. Get your fingers under TEMPLATE 2 through one of the cutaways, and pull; you will reuse this piece to make your next Chembuster. Now put TEMPLATE 3 back in its place at the top of the copper pipes.

Continue pouring the resin + metal shavings in two phases so the resin hardens quicker. Do not move the device until resin has hardened completely.

Now you’re done! Once resin has hardened, move your new Orgonite Chembuster to your favorite, safe and secret, but most of all, strategic location. Disattach the 5 foot copper pipes for increased portability. Carry the bucket. You can paint the bucket a darker color–green or brown if you like–to reduce visibility.

–Positive Energy For All . . .